Zap-A-Gap CA+ (super glue) *Parts: Q-Car Company: Scale ruler (for the scale you’re working in) Testors: Single edge razor blades (as replacements for Chopper or instead of X-acto knife) List of Suggested Tools & Glues and Partsįor This Project Tools & Glues: NorthWest Short Line: The photos on this page can be enlarged by clicking on them. The clearance under the el shouldīe between 15 to 20 scale feet, but can be less depending on the situation. Out of the material used and the dimensions figure easier. Simplify this further, shortening the length to 48 scale feet or 12 inches, you can get more The length works out to 50 scale feet or 12-1/2 inches. For instance, in O scale, the depth of the girders should be a When joiningĭissimilar parts, such as styrene to metal, a "super" glue is used.įollowing the drawings and descriptions used in the book mentioned above, one can scale down This liquid will actually melt the pieces together to create a strong joint. The best glue to use to join the styrene pieces is Testors liquid cement (or similar product). Using this tool or any tool, follow the operating instructions and safety precautions Size consistently, making it easy to collect enough parts to build in mass. Shop doesn’t have them in stock, they can usually order just what you want.Ĭutting these strips and shapes to length in quantity is the key to building the structure,Īnd a tool called "The Chopper II",from Northwest Shortline, Styrene was chosen here because it is easily cut and there is anĮxcellent variety of shapes and sizes currently available. "Building The New Rapid Transit System of New York City Circa 1915"įor this project, we will be using styrene plastic strips and structural shapes that areĬommercially available. This design was very standardized and simplified from previous elĬonstruction and is easily adapted, and reduced to O scale - or any scale for that matter.Īn excellent source of information regarding this type of structure is the book, This type of structure can be found on lines including - Astoria, Flushing, West End, Culver,Īnd IRT lines in the Bronx. The structure modeled here is based on the city built "dual contracts" design. Being inspired by the great model structures of Nate Gerstein, Joseph Frank, and Bob Olson, I have set out to build my own! This page shows ways to build NYC style El structure. If they are as good as the Chopper, then they should be wonderful.Modeling New York City Elevated Structure While you’re looking into these guys, have a look at their other products. I know that I’ve been more than happy with mine. If you have projects that require clean, repetitive cutting, I suggest you look into these Chopper II tools by the NorthWest Short Line Company. This might be the best tool I’ve bought for a while. I found that cutting the parts for these wood kits with The Chopper II not only dramatically improved the over all quality, but sped up the process by a factor of about 10. These “angle stops” make repetitive cuts of the same length nothing short of “way easy.” The unit also has a number of different angles for cutting that are printed right on the cutting face which come in very handy! The Chopper II has four “angle stops” that are easily adjusted to your work. The actual cutting is done with a single edged razor blade that is easily replaced (keep some extra blades around for replacement). It’s made of high-quality metal with a high-density cutting board. And all I can say is “Wow!” I really should’ve had this tool years ago! This tool is a truly marvelous addition to my workbench. All kinds of stuff!Īfter some careful consideration, I bought a Chopper II tool from them. (I found out that they offer a full line of modeler tools, books, parts, motors and gears. On a new quest, I started to talk with other modelers and they directed me to the folks at NorthWest Short Line Company. In the past, I would measure and mark each piece and then cut it with my flush cut “nippers.” This worked “kind of,” but the final result was, at best, poor and inconsistent. With all these kits to build, I could see that I needed to get better at making cuts on these parts. You can never have too many models on your layout, especially if they are high quality wood kits. And lately, I’ve been working a lot with wood kits (buildings and bridges mostly). I find the different aspects to be the most enjoyable part. I have a lot fun with my model railroading hobby.
0 Comments
Leave a Reply. |